BLOG


Weld inspection
This article shows a video of a multi-group weld inspection, using 2 phased-array and a pair of TOFD probes. With
Read more.
Characterization of misoriented notch
Tilted defect reconstruction with TFM technique and mode conversion with a probe of 5 Mhz, 64 elements, and a S
Read more.
Solid Railway Axle inspection
With an aperture of 64 elements and a customized wedge, GEKKO can focus the energy farther in the component and
Read more.
Flange corrosion
TFM and PAUT combined on flange face corrosion: A dedicated application developed by Buffalo Inspection. GEKKO and the TFM function
Read more.
Industrial system for composites inspection using SAUL
SAUL NDT for Airbus A350 composite parts ©Stelia Aerospace Composites     The SAUL technique enables the transmission of an
Read more.
Cladded samples
GEKKO can inspect cladded materials using dual matrix arrays and/or TFM with the full 64-element aperture.
Read more.
High temperature hydrogen attack (HTHA)
HTHA damage is detected using AUBT method (Advanced Ultrasonic Backscattering Technique) that evaluates the frequency and velocity dependence to a
Read more.
TFM image of a polyethylene sample joined by electrofusion
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies Here is a TFM image obtained on a polyethelene pipe using a
Read more.
Polyethylene weld inspection using TFM
Guillaume Neau, VP sales M2M products at Eddyfi Technologies, explaining the TFM imaging of a polyethylene weld inspection, using a 2MHz
Read more.
GEKKO recognized in Shell Tiger Times
February 2018 The Shell Geismar Tiger AO4 project has been saving time using the phased-array flaw detector GEKKO to inspect
Read more.
Nozzle-to-pipe inspection from the nozzle side
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies A while back we posted an article showing the application developed for
Read more.
Acquisition of the Full Matrix Capture (FMC) data for post-processing
By Frédéric REVERDY, Business Development Manager in M2M While both the Gekko and the Mantis were developed for the field,
Read more.
Inspection of a small nozzle with GEKKO
By Frédéric REVERDY, Business Development Manager in M2M We looked at a small nozzle (1" diameter) with a 5L16 small
Read more.
CAPTURE (Gekko and Mantis software) 2.1 version release
By Frédéric REVERDY, Business Development Manager in M2M The new version of the Capture software (Gekko and Mantis software) was released.
Read more.
Multi-group weld inspection using MANTIS
This article shows a video of a multi-group weld inspection, using 2 phased-array and a pair of TOFD probes. With
Read more.
Time Corrected Gain (TCG) for TFM in GEKKO
By Frédéric REVERDY, Business Development Manager in M2M We use a 5L64 linear phased-array probe with a L0 wedge over
Read more.
Y-joint inspection
By Frédéric REVERDY, Business Development Manager in M2M A while back we had a post about a T-joint inspection with
Read more.
Incomplete root penetration (bridging) on a T section
By Frédéric REVERDY, Business Development Manager in M2M Detection of an incomplete root penetration (bridging) on a T section. The
Read more.
Surface breaking crack characterization with TFM
By Frédéric REVERDY, Business Development Manager in M2M A while back I had a post about surface breaking crack characterization
Read more.
Surface breaking crack characterization using TFM
By Frédéric REVERDY, Business Development Manager in M2M Surface breaking crack characterization using TFM on the same side as the
Read more.