BLOG ch


M2M Fast TFM Eddyfi Technologies
Need for Speed…TFM Speed ch
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies   Back in 2014, M2M now Eddyfi, was the first one on the
Read more.
M2M Fast TFM Eddyfi Technologies
Need for Speed…TFM Speed
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies   Back in 2014, M2M now Eddyfi, was the first one on the
Read more.
Matrix array with the M2M Gekko ch
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies Matrix arrays can inspect a full volume by steering the ultrasonic energy in
Read more.
Analysis on M2M Gekko Capture 2.3
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies The following image is an inspection done with two phased-array probes. In the
Read more.
Analysis on M2M Gekko Capture 2.3
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies The following image is an inspection done with two phased-array probes. In the
Read more.
Why 64 elements?
By Guillaume Neau, VP M2M business development at Eddyfi Technologies Here is an example of the importance of the probe aperture
Read more.
Delay law Focalization in M2M Gekko
Delay laws are in essence what phased-array technique is all about. We can electronically scan, steer and focus the energy
Read more.
curved wedge calibration
Curved wedge calibration in M2M Capture V2.3 software
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies A sneak preview of one of the many features that will be
Read more.
New tools to avoid missing data in M2M Capture
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies The right scanning speed depends on the PRF of the equipment, the soundpath
Read more.
Delay law calculator extended in M2M Capture V2.3
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies Another peak view at the 2.3 version of M2M Capture coming up
Read more.
Delay law calculator extended in M2M Capture V2.3
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies Another peak view at the 2.3 version of M2M Capture coming up
Read more.
Wizard to check the angle/height of a wedge
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies A sectorial view is based on the ultrasonic and geometrical parameters of
Read more.
curved wedge calibration
Curved wedge calibration in M2M Capture V2.3 software
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies A sneak preview of one of the many features that will be
Read more.
FMC data analysis with the Gekko and CIVA Analysis zh
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies FMC data analysis with the Gekko and CIVA Analysis The Gekko and
Read more.
Pitting detection with TFM and MANTIS
Here is a comparison of a linear scanning using 8 elements focused close to the backwall and a TFM using
Read more.
Casting Test
Shrink Hole Indication
Read more.
Offshore Wind Power T-joint construction weld
Application of TFM for defect sizing in welded joints. These below pictures show T-joints at the offshore windmill construction. The material
Read more.
Austenitic welds
Ultrasonic inspection of austenitic welds is qualified for in-service inspection since beginning of 2000’s. Implementation of the solution based on
Read more.
PAUT T-joint inspection
  Crack detection in a T-joint using GEKKO. We are looking at a 5-mm under-bead crack in one of the
Read more.
Inconel weld-inspection
Using Total Focusing Method (TFM) for the inspection of inconel weld, a extended vizualisation area is obtained. Defects are detected
Read more.