Mantis应用


 

Below are application cases using the streamlined CAPTURE interface (available in MANTIS and GEKKO).

M2M Fast TFM Eddyfi Technologies
Need for Speed…TFM Speed
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies   Back in 2014, M2M now Eddyfi, was the first one on the
Read more.
Analysis on M2M Gekko Capture 2.3
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies The following image is an inspection done with two phased-array probes. In the
Read more.
Delay law calculator extended in M2M Capture V2.3
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies Another peak view at the 2.3 version of M2M Capture coming up
Read more.
curved wedge calibration
Curved wedge calibration in M2M Capture V2.3 software
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies A sneak preview of one of the many features that will be
Read more.
Pitting detection with TFM and MANTIS
Here is a comparison of a linear scanning using 8 elements focused close to the backwall and a TFM using
Read more.
Casting Test
Shrink Hole Indication
Read more.
Offshore Wind Power T-joint construction weld
Application of TFM for defect sizing in welded joints. These below pictures show T-joints at the offshore windmill construction. The material
Read more.
Austenitic welds
Ultrasonic inspection of austenitic welds is qualified for in-service inspection since beginning of 2000’s. Implementation of the solution based on
Read more.
PAUT T-joint inspection
  Crack detection in a T-joint using GEKKO. We are looking at a 5-mm under-bead crack in one of the
Read more.
Inconel weld-inspection
Using Total Focusing Method (TFM) for the inspection of inconel weld, a extended vizualisation area is obtained. Defects are detected
Read more.
PMMA inspection
This video shows an electronic scanning of a PMMA (polymethyl methacrylate also called acrylic glass) plate using the flaw detector
Read more.
Small diameter pipe inspection
In this case, a cylindrical reconstruction is being done for small diameter pipe inspection using sizing with corner effect mode
Read more.
Weld inspection
This article shows a video of a multi-group weld inspection, using 2 phased-array and a pair of TOFD probes. With
Read more.
High temperature hydrogen attack (HTHA)
HTHA damage is detected using AUBT method (Advanced Ultrasonic Backscattering Technique) that evaluates the frequency and velocity dependence to a
Read more.
Nozzle-to-pipe inspection from the nozzle side
By Frederic Reverdy, M2M Product Sales Specialist at Eddyfi Technologies A while back we posted an article showing the application developed for
Read more.
Acquisition of the Full Matrix Capture (FMC) data for post-processing
By Frédéric REVERDY, Business Development Manager in M2M While both the Gekko and the Mantis were developed for the field,
Read more.
CAPTURE (Gekko and Mantis software) 2.1 version release
By Frédéric REVERDY, Business Development Manager in M2M The new version of the Capture software (Gekko and Mantis software) was released.
Read more.
Multi-group weld inspection using MANTIS
This article shows a video of a multi-group weld inspection, using 2 phased-array and a pair of TOFD probes. With
Read more.
Cracks in clads
It is possible to detect cracks in the cladding using TFM by focalizing the energy everywhere and using a large
Read more.
Nozzle inspection
M2M has developed a unique nozzle inspection application that allows: - to define a nozzle geometry on board - to display in
Read more.